Pressure Systems 9022 Uživatelský manuál Strana 65
- Strana / 194
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Pressure Systems, Inc. NetScanner™ System (9016, 9021, & 9022) User’s Manual
www.PressureSystems.com
3 - 35
NOTE: With the exception of binary formats 7 and 8, all other
formats include a leading space in each datum delivered
in each stream packet.
The ‘f’ parameter identifies the format of each selected acquired datum in each
stream packet, and is a single numeric digit. Valid format codes are listed in the
following table:
f
converts each internal selected acquired datum value from.. max. char.
0 single binary float to 7-10-digit signed decimal “ [-xxx]x.xxxxxx” 13
1 single binary float to 8-digit hex integer “ xxxxxxxx” 9
2 double binary float to 16-digit hex integer “ xxxxxxxxxxxxxxxx” 17
5 single binary float to long integer (EU*1000) then to 8-digit hex integer 9
7 single binary float to single binary float (big endian: msb first) 4
8 single binary float to single binary float (little endian: lsb first) 4
Unless the EU conversion scalar is altered, the returned pressure data will be in units
of psi. (See command ‘v’, array 11, coefficient 01 for other units.
The number of stream packets (‘num’) parameter is a positive integer count (from
0 to 2147483647, specified with 1 to 10 numeric digits as needed). It sets a finite
limit on the number of packets delivered in the host data stream. The value 0 for
this parameter requests “continuous” output packets for the defined host stream
(unbounded).
- Intelligent Pressure Scanner 1
- User’s Manual 1
- Our Company 5
- Our Warranty 5
- Technical Support 5
- Merchandise Return Procedures 5
- Website and E-Mail 6
- Our Firmware 6
- Our Publication Disclaimer 6
- Table of Contents 7
- Table of Contents (Cont.) 10
- Appendices 10
- List of Figures 11
- List of Tables 11
- Chapter 1 12
- General Information 12
- 1.3 Options 15
- Chapter 2 18
- Installation and Set Up 18
- 2.3 Preparation for Use 19
- Figure 2.2 20
- Figure 2.3 23
- Ethernet Network Topology 23
- Diagnostic Port Hookup 24
- 2.3.6 Pressure Connections 24
- 2.3.8 Case Grounding 30
- 2.3.9 Trigger Input Signal 30
- Chapter 3 31
- Programming and Operation 31
- 3.1.2 Commands 32
- 3.1.3 Responses 35
- Table 3.2 43
- 3.3 Obsolete Commands 109
- Chapter 4 111
- Calibration 111
- Figures 4.1 - 4.4 113
- 4.2 Re-zero Calibration 114
- 4.3 Span Calibration 116
- 4.5.1 Setup 124
- 4.5.2 Calibration Procedure 125
- 4.6 Coefficient Storage 129
- 4.8 Line Pressure Precautions 134
- Chapter 5 135
- 5.1.1 Common Maintenance 137
- 5.1.2 Module Disassembly 139
- PC-316 Board 143
- 5.1.6 Replacement of O-Rings 147
- 5.2 9022 Excitation Trim 153
- Setting (JB1) 154
- 5.4 Upgrading Module Firmware 155
- Chapter 6 157
- Troubleshooting Guide 157
- 6.3 User Software 165
- Chapter 7 166
- Appendix A 168
- Appendix B 170
- Appendix C 172
- NetScanner 173
- P/N 9080 173
- 9080 Cable 174
- 9096 Cable 175
- 9400/9021 (D-Shell) Cable 175
- Calibration Cable (9022) 179
- Appendix D 182
- 9016 Mounting Dimensions 183
- 9021 Mounting Dimensions 184
- 9022 Mounting Dimensions 185
- Appendix E 186
- Appendix F 190
- Appendix G 192
Související produkty a manuály pro Měření, testování a kontrola Pressure Systems 9022
(194 stránky)Autostart AS-2660i TW-FM podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Alarm samochodowy Autostart AS-2660i TW-FM.
Dostarczamy 3 pdf podręczników Autostart AS-2660i TW-FM do pobrania za darmo według typów dokumentów: Podręcznik Użytkownika, Przewodnik Instalacji, Instrukcja Użytkownika
Komentáře k této Příručce